|
Wireless Keypad-IC OLD STYLE BLACK
GWKIC
& ACSDG
INSTALLATION AND PROGRAMMING
INSTRUCTIONS
- INSTALLATION
INSTRUCTIONS
- BASIC
PROGRAMMING
- PROGRAMMING MULTIPLE
DOOR OPERATORS
- ENHANCED PROGRAMMING
Features
-
Controls up to three doors.
-
Panic control –
Once control is established and for 30 seconds
thereafter, any button will control door.
-
Two Permanent Personal Identification Numbers
(PIN).
-
Temporary PIN for special purpose access.
-
Any PIN can be up to 8 digits long.
-
Lighted Keypad for ease of use at night.
-
Indicator Light gives visual confirmation of
key presses.
************* WARNING *************
Moving Door can cause serious injury or death.
·
DO NOT install
transmitter unless the door operator’s safety reverse works as required
by the door operator’s manual.
·
Wall control
must be mounted in sight of door, at least 5 feet above floor and clear of
moving door parts.
·
Keep people
clear of opening
while door is moving.
·
DO NOT
allow children to
play with the transmitter or door operator.
If
safety reverse does not work properly:
·
Close door
then disconnect operator
using the manual release handle.
·
DO NOT
use transmitter
or door operator.
·
Refer to Door
and Door Operators Owner’s Manuals before attempting any repairs.
_________________________________________________
Electrical Shock can cause serious injury or death.
·
Power cord must be unplugged before attaching any wires,
·
Be sure wire ends do not touch each other or other terminals.
If you have questions or if you need a manual, contact the distributor or
manufacturer of the operator.
******************************************************************************************************************************
1. INSTALLATION INSTRUCTIONS
NOTE:
For convenience in programming you may wish to install Wireless Keypad after
Basic Programming of Wireless Keypad and Garage Door Operator(s) is completed.
·
Mount
wireless keypad on a flat vertical surface with enough room above to slide cover
up. pick location out of
path of moving garage door and supporting hardware.
·
Slide Keypad Cover up and pull off
wireless keypad. Slide off battery cover and remove battery.
·
Mark two holes by tapping a small
nail through screw holes on keypad. Drill 1/16’ pilot holes then fasten with #6
screws enclosed. Replace Keypad cover.
·
Replace battery and slide battery
cover back into place.
2. BASIC PROGRAMMING
How to enter Personal
Identification Number (PIN 1).
How to reset the Wireless
Keypad memory.
A. PROGRAMMING THE WIRELESS KEYPAD
Entering PIN 1
ACTION
KEYPAD INDICATOR
Open cover fully
Blinks once and goes out
Press 3-5-7
Press “PROG”
Blinks once each second
Enter PIN 1 (up to 8 digits)
Press “PROG”
Double blinks each second
Close cover fully
NOTE: Your
wireless Keypad is now ready to signal your Door Operator. Your Door
Operator must be programmed to accept the signal from your Wireless Keypad.
Resetting the
Wireless
Keypad-------------------------------------------------------------------------------
·
Open cover half way.
·
Press and hold “PROG” and “8”
while fully opening cover
·
INDICATOR will blink once and go
out.
·
Close cover fully.
NOTE:
Wireless Keypad memory is now set the same as
when it left the factory.
Return
to Entering PIN 1.
B. PROGRAMMING 1 DOOR OPERATOR
How to program your Door Operator to receive the signal from your Wireless
Keypad.
************* WARNING *************
During this
programming the Door Operator could begin to run. Be sure to stay away from the
moving door and it’s parts. To prevent the door from moving, close door then
disconnect it from the Door Operator by pulling the Red Emergency Release
Handle.
Find the Learn Code Button
and Radio Signal Indicator located on the Door Operator power head. Open
Wireless Keypad Cover fully. This can be found where you
see the antenna wire hanging from the motor head (you may have to take the lens
cover off). If antenna wire is not hanging from motor head then you have an
external receiver which is a black box approx. 6" x 2" mounted somewhere in the
garage with a antenna wire hanging from it (pop off cover to find Learn Code
Button).
ACTION
KEYPAD INDICATOR
Press Operator Learn Code
Button Blinks
Enter PIN 1
Press “SEND” Stays on
Press “SEND” Goes out
Press “SEND” to Test System Motor Runs.
Press “SEND” to Test System Motor Stops.
Use the Emergency Release
to reconnect the Door to the Door Operator. Your system is now ready to use.
C. CONTROLLING 1 DOOR OPERATOR
ACTION
KEYPAD INDICATOR
Open
Cover
Wait for Keypad indicator to go out before
Pressing any buttons.
Enter PIN1
Indicator blinks with each key press.
Press and hold "SEND"
Door moves if only 1 door.
Close cover fully
NOTE:
- if indicator is solid, PIN 1 was entered correctly.
-
if indicator blinks, PIN1 was entered incorrectly. Close cover and start
C.
CONTROLLING 1 DOOR OPERATOR over.
NOTE:
Any Keypad button will control the door within 30 second after door begins to
move or until cover is closed.
3. PROGRAMMING MULTIPLE DOOR OPERATORS
How to add Door Operators 2
and 3 to Wireless Keypad.
How to program your door
Operator to receive the signal from your Wireless Keypad.
************* WARNING *************
During this
programming the Door Operator could begin to run. Be sure to stay away from the
moving door and it’s parts. To prevent the door from moving, close door then
disconnect it from the Door Operator by pulling the Red Emergency Release
Handle.
A. ADDING MORE DOORS TO THE WIRELESS KEYPAD
ACTION
KEYPAD INDICATOR
Open cover fully
Blinks once and goes out
Enter PIN 1
Press “PROG”
Blinks once each second
Press “PROG”
Double blinks each second
Press “PROG”
Triple blinks each second
Enter total number of doors (2or3)
Press “PROG”
Goes out
Close cover fully.
NOTE: Your
Wireless Keypad is now ready to signal your door operators. Each Door Operator
must be programmed to accept the signal from your Wireless Keypad. Decide which
Door Operator will be Door 1, Door 2 and Door 3.
B. PROGRAMMING MULTIPLE DOOR OPERATORS
Find the Learn Code Button
and Radio Signal Indicator located on the Door Operator power
Head Open Wireless Keypad
cover fully.
ACTION
RADIO SIGNAL INDICATOR
Press Operator Learn Code Button
Blinks
Enter PIN 1
Press “SEND”
Enter Door Number (1,2or 3)
Stays on
Press “SEND”
Goes out
Press “SEND” to Test System
Motor Runs
Press “SEND” to Test System
Motor Stops
Close Wireless Keypad cover fully
Use the Emergency Release
to reconnect the Door to the Door Operator. Your system is now ready to use. If
you are programming another Door Operator go to that machine and repeat the
above steps.
C. CONTROLLING MULTIPLE DOOR OPERATORS
ACTION
KEYPAD INDICATOR
Open cover Wait for keypad
indicator to go out
before pressing any buttons.
Enter PIN 1 Indicator
blinks with each key press.
*Press “SEND”
*Enter Door Number (1,2 or 3)
Door moves.
Close cover fully
NOTE: -
if indicator is solid, PIN was entered correctly.
- if
indicator blinks, PIN was entered incorrectly. Close cover and start
C.
CONTROLLING MULTIPLE DOOR OPERATORS over.
NOTE: Any
Keypad Button will control the door within 30 seconds after door begins to move
or until cover is closed.
4. ENHANCED PROGRAMMING
How to add a Second Personal Identification Number (PIN2).
How to change Personal Identification Number (PIN 1 or PIN 2).
How to add and cancel a Temporary Personal Identification Number (PIN).
Changing a PIN ACTION
KEYPAD INDICATOR
Open cover fully Blinks
once and goes out.
Enter PIN to be changed
Press “PROG” Blinks
once each second
Enter New PIN
Press “PROG” Double
blinks if PIN 1 changed
Goes out if PIN 2 changed
Close cover fully
NOTE: Your
Wireless Keypad is now ready to signal your Door Operator(s). Your Door
operator(s) must be programmed to accept the signal from your Wireless Keypad.
SEE
2B
PROGRAMMING 1 DOOR OPERATOR OR 3B PROGRAMMING MULTIPLE
DOOR OPERATORS.
Adding
PIN 2 ACTION
KEYPAD INDICATOR
Open cover
fully Blinks once and
goes out
Enter 1-5-9
Press “PROG”
Blinks once each second
Enter PIN 2 (up to 8
digits)
Press “PROG”
Goes out
Close cover fully
NOTE:
Your Wireless Keypad is now ready to signal your Door Operator(s). Your Door
Operator(s) must be programmed to accept the signal from your Wireless Keypad.
SEE 2B PROGRAMMING 1 DOOR OPERATOR or
3B PROGRAMMING MULTIPLE
DOOR OPERATORS.
Adding
Temporary PIN
ACTION
KEYPAD INDICATOR
Open cover fully
Blinks once and goes out
Enter PIN 1
Press
“PROG” Blinks once each
second
Press
“PROG” Double Blinks each
second
Enter Temporary PIN
Press
“PROG” Triple blinks each
second
Close cover fully
NOTE:
Your Wireless Keypad is now ready to signal your Door Operator(s). You do not
need to reprogram your Door Operator(s).
Cancelling the Temporary
PIN____________________________________________________________
The
Temporary PIN will remain active until the next time PIN 1 is entered. Entering
PIN 1 cancels the Temporary PIN.
|
