|
INTELLICODE SERIES II TRANSMITTER
GITR-3,
G2T-1, G2T-2, G2T-3, GIT-1, GIT-2, GIT-3, GICT390-1, GICT390-3, GICTD-1,
GICTD-3, GITR-3
1.
IMPORTANT INFORMATION
USE
ONLY WITH SERIES II ELECTRONICS.
Older Transmitters and Receivers will not work
with the new electronics. There are no Security Code Switches inside Door
Operators, Transmitters and Receivers.
************* WARNING *************
Moving Door can cause serious injury or death.
·
DO NOT install
transmitter unless the door operator’s safety reverse works as required
by the door operator’s manual.
·
Wall control
must be mounted in sight of door, at least 5 feet above floor and clear of
moving door parts.
·
Keep people
clear of opening
while door is moving.
·
DO NOT
allow children to
play with the transmitter or door operator.
If
safety reverse does not work properly:
·
Close door
then disconnect operator
using the manual release handle.
·
DO NOT
use transmitter
or door operator.
·
Refer to Door
and Door Operators Owner’s Manuals before attempting any repairs.
_________________________________________________
Electrical Shock can cause serious injury or death.
·
Power cord must be unplugged before attaching any wires,
·
Be sure wire ends do not touch each other or other terminals.
If you have questions or if you need a manual, contact the distributor or
manufacturer of the operator.
******************************************************************************************************************************
A different Transmitter Code is set at the factory for each SERIES II
INTELLICODE Transmitter.
2. TO
PROGRAM THE RECEIVER
·
Locate the Learn Code Button and Radio Signal Indicator on the
Power Head Receiver of your Door Operator. This can be found where you
see the antenna wire hanging from the motor head (you may have to take the lens
cover off). If antenna wire is not hanging from motor head then you have an
external receiver which is a black box approx. 6" x 2" mounted somewhere in the
garage with a antenna wire hanging from it (pop off cover to find Learn Code
Button).
·
Press and release the Learn Code Button. The Radio Signal
Indicator will blink approximately 2 times per second.
·
Press the Transmitter Button once within 30 seconds. The
Radio Signal Indicator stays lit – SOLID.
·
Press the Transmitter Button once within 30 seconds.
The Radio Signal Indicator will go out ( the Transmitter Code ins now stored in
memory).
NOTE: If a second Transmitter Code is not confirmed within 30 seconds or
if a different Transmitter Code is sent, the Radio Signal Indicator will blink
approximately 4 times per second, then programming will stop. If programming
stops, repeat all steps again.
·
Repeat all steps for each Transmitter, Wireless Keypad or other
access device to be learned.
NOTE: A maximum of 7 Transmitter, Wireless Keypad and other access device
Codes can be stored in Receiver Memory. If a Transmitter becomes lost or if
you want to delete a Transmitter, Wireless Keypad or other access device,
proceed to ERASING ALL RECEIVER MEMORY.
NOTE: If you are replacing a lost or stolen Transmitter: (1) Erase ALL
Transmitter Codes from the Receiver memory. (2) Reprogram the Receiver with
the remaining Transmitters Codes.
3.
MULTI-BUTTON TRANSMITTERS
NOTE: Only ONE button of a Multi-Button Transmitter can be
programmed into a single Receiver. The other buttons are to control other Door Operators.
4. ERASING
ALL RECEIVER MEMORY
·
Press and HOLD the Learn Code Button for 10 seconds or until
Radio Signal Indicator goes out.
·
ALL TRANSMITTER CODES ARE ERASED FROM RECEIVER MEMORY.
·
Reprogram the Receiver with the remaining Transmitter Codes by
repeating all steps in number 2.
5. BATTERY
/ VISOR CLIP INSTALLATION
·
Turn Transmitter upside down.
·
Battery replacement (your Transmitter in battery powered).
Gently push straight IN on tab (slot) with a coin or small screwdriver. Battery
cover snaps open.
·
Install new battery in same position. Press battery cover
until it snaps back in place.
·
ATTACH VISOR CLIP to Transmitter. Slide Visor Clip into
back of case until it snaps into place.
6.
TRANSMITTER OPERATION
·
Point Transmitter at the garage door and press the button.
Door will move.
·
Press the Transmitter Button again and the door will stop.
·
Press the Transmitter Button again and the door will move the
other way. The door automatically stops at the end of the open or close cycle.
|
