Stanley or Stanley
Instructions for Keyless Entry 49442
STANLEY KEYPAD CODING INSTRUCTIONS
READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING
The CodeKey Entry System is a wall-mounted, battery-operated keypad that allows
anyone to operate the garage door opener as long as that person enters a
specific 4-digit ACCESS CODE which is programmed by the owner.
The keypad is back lit with LEDs which are normally off. Pressing ANY key lights
the keypad. Each keystroke causes a separate indicator to blink.
The correct "ACCESS CODE" must be entered within 20 keystrokes,
otherwise the unit will stop operation for 5 minutes. The user has 25 seconds
between keystrokes to enter the correct code, otherwise you must start over.
After the CodeKey has activated by entering the correct (in sequence)
"ACCESS CODE", the Stanley Safe-T-Close mode allows ANY key on the
CodeKey to be used to open, stop or close the door, for a period of about thirty
A LOW BATTERY condition is indicated when the keypad lights on the CodeKey go
off after the first keystroke entry instead of remaining on.
Important: The installer MUST program the RADIO CODE and ACCESS CODE
before the CodeKey will operate the door opener
If you are mounting your keyless entry system to aluminum siding you may find it
better to substitute carriage bolts for the mounting screws provided. Bolts
should be long enough to reach into the garage and be secured with lockwashers
and nuts. If you are mounting your keyless entry system onto brick, stone or
mortar, suitable anchors must be set into the mortar, and the fasteners screwed
IDENTIFYING YOUR "RADIO CODE" TYPE
Before setting any codes you need to identify the type of receiver that is in
your door opener. You do this by looking at the rear of the power unit hanging in
your garage. If your opener has a "LEARN" (remote) button on
the back, you have a SecureCode type opener. If your opener has a series
of toggle switches or jumper wires, you have a Digital type opener.
Identify the type of opener you have at this time.
If you have a SecureCode type opener, go immediately to the Setting
the "Access Code" section. If you have a Digital type of
opener, you first will have to write down the code setting of the opener. Each
toggle switch that is turned ON (closed) or jumper wire that is NOT cut
determines the "Radio Code" your CodeKey keypad must be programmed to
*If you have toggle switches, write down the numbers that appear below the
switches that are turned ON (closed). Example: If Switches numbered 1,2,4,6,9,0
are ON (closed), 1-2-4-6-9-0 will be your "Radio Code". * If you have
jumper wires, write down the number of the unclipped wires (ON). Example: If
wires 4,8,10 are unclipped, 4-8-0 ill be your "Radio Code".
Note: A "Radio Code" with ALL positions open (OFF) or ALL
jumper wires clipped can NOT be used.
SETTING THE "ACCESS CODE"
The ACCESS CODE is a 4-digit code picked by you (sort of a PIN number) which is
used to activate the CodeKey unit. The FACTORY SET access code is 1-2-3-4. To
change the access code follow these steps:
A. Press the ACCESS LEARN key two (2) times. The red indicating light
will blink each time the key is pressed, then it will stay on.
B. If this is the first time the CodeKey is being programmed, enter the FACTORY
SET code of 1-2-3-4. If not, enter the access code that was previously
C. Enter the NEW access code you selected.
D. Press ACCESS LEARN one more time. This eliminates the old access code
and installs your new code. If the LED flashes quickly for a few seconds, you
will have to re-enter the data because it was not entered correctly.
SETTING THE "RADIO CODE"
At the keypad enter the code as follows:
A. Press the RADIO LEARN key two (2) times. The red indicating light will
blink each time the key is pressed then it will stay on.
B. Enter the "Radio Code" that you determined is set on your power
C. Press RADIO LEARN one more time. The red LED should turn off. If the
LED flashes quickly for a few seconds, you will have to re-enter the data
because it was not entered correctly.
TO OPERATE YOUR GARAGE DOOR
CAUTION: Door opener will activate during the following steps. Keep pathway of
garage door clear.
Plug in your door opener at this time. If you have a DIGITAL type opener,
entering the four digit ACCESS CODE you selected will activate your door. If you
have a SECURECODE type opener, you must first follow these steps to teach the
opener the radio code the CodeKey system is sending.
A. Press and release the LEARN button located on the rear of the power
unit. The red LED indicator above the LEARN button and on the power unit
will come ON, indicating the power unit is now in the LEARN mode.
B. Immediately enter the 4-digit ACCESS CODE you selected in the CodeKey
keypad. The CodeKey will send a radio signal to the power unit, then the lights
on the power unit will blink two (2) times and turn OFF.
C. Press ANY key on the CodeKey keypad. This will activate the power unit. The
power unit "learned" this new radio code.
If at any time you get confused or forget the existing ACCESS CODE, you can
RESET the CodeKey to the factory settings. You do this by both pressing the ACCESS LEARN and RADIO LEARN buttons together for ten (10) seconds. This
will automatically set the ACCESS CODE to 1-2-3-4, and the RADIO CODE to 0-0-0-0
(this is the SecureCode type setting).
The CodeKey will always "remember" the last codes you programmed even if the
battery is removed. A 9-volt battery is used.